Advanced XP 2K

Advanced XP 2K

Product form

SKU: 690146US

  • For high traffic, commercial floors.
  • Our premium 2K water based finish
  • Green building compliant
  • R10 slip resistance
  • Superior performance

Engineered to meet the toughest challenges of high-traffic commercial and demanding residential spaces, our Advanced XP 2K finish is the best choice for a long lasting, durable floor. This water-based, two-component finish boasts exceptional scratch, wear, water, and stain resistance, with an added layer of extra slip resistance for increased safety. It's formulated with non-yellowing resins and fortified with UV absorbers to help safeguard the wood against harmful UV exposure, while delivering an ultra-durable film with a rich, full appearance. With the lowest VOC's of any major competitor, you can rest assured of a healthy indoor air quality.

Product details


VOC: 85 g/l. (max)

Density: 1.00-1.10 g/ml.

pH-value: pH 7-8

Shelf life: 2 years

Application Temperature: +59-77°F and approx. 50% air humidity.

Coverage: 325-410 sq.ft./Gal

Colors: Colorless - Satin

Cleaning of tools: Use water

Storage: +50-77°F. Keep out of reach of children. Do not expose to heat (e.g. sunlight). Store frost-free during winter and cool during summer.

Packaging: 1 Gallon

Non-slip (DIN 51130): R10

Viscosity: 20-25 Sec. DIN Cup 4

Pot life: The mixture must be used within 5 hours. Shake/stir thoroughly before use.

Odor: Characteristic

Solid content: 30-40%

Mixing ratio: 10% or 16.907 FL.OZ. to 169.070 FL.OZ. lacquer

Between coats: 2-3 hours at 68°F

Light use: 4-6 hours at 68°F

Recommendation: Wait 24 hours before putting furniture on the floor. Wait 5 days before covering with carpets and mopping. If drying times are not followed, this can result in poor adhesion and reduced resistance. For each coat of floor finish, drying times will be increased. High temperature and low air humidity will reduce drying times. Low temperature and high air humidity will extend drying times.

Fully hard: 5 days at 68°F

It is important that both wood and floor finish have a temperature of min. 59°F (preferably around 68°F) and air humidity of approx. 50%. Make sure that the room is well-ventilated for optimal evaporation and drying time. For the final sanding to bare wood, use grit 100-120 sandpaper or sanding pad. Vacuum thoroughly and tack the floor afterwards, using a tightly-wrung water-soaked mop/cloth. The floor must be completely dry before sealing. When sealing, use WOCA Sealers for newly sanded wood to reduce side bonding.
Always remember to test on a less visible spot to check the compatibility of the surface with the product.

1. Apply the sealer if not using a stain. When dry, mix Advanced Hardener US with the floor finish and shake thoroughly before use. Leave the mixture to stand for ten minutes before use, to allow the hardener to activate.
2. A coat of Advanced XP 2K US Lacquer should be applied undiluted, using a brush or roller. Leave the surface to dry until next day.
3. Sand the surface with 120-200 and vacuum clean the surface thoroughly.
4. Apply the final coat of Advanced XP 2K US with hardener (freshly mixed).
Water and colored fluids, such as red wine and coffee, must be wiped off immediately to prevent staining.
Technical Data Sheet
Safety Data Sheet

All floor coating products marketed in France are obliged to certify their products with an A+. The aim is to improve indoor air quality and, at the same time, enable consumers to choose environmentally friendly products.

DIBt is a German institute that tests and issues technical approvals for building materials. The goal is to improve the working environment for floor installers while ensuring a safe indoor air quality for the final consumer.


Danish Indoor Climate Label is a voluntary labeling system for products and materials which can document the effect of off gassing. Indoor climate labeled materials are a natural component in sustainable construction, where a good indoor air quality contributes to social sustainability.

Anti Slip R10 DIN 51130 is a standardized anti-slip test for flooring. WOCA Diamond Oil Active, Exterior Oil, RP 2K and XP 2K Water Based Finishes, and UV Oil 510 have been tested on solid wood, and achieved a R10 classification according to DIN 51130.

The migration of metals (As, Hg, Se, Cr, Sb, Cd, Pb, Ba) of the sample was tested according EN 71 Part 3 1995. There was no evidence for migration of the named metals above the limit of detection (10-50 ppm). All interior WOCA products are suitable for toys.

Fire Classification EN 13501-1:2018 WOCA XP 2K Water Based Finish has been tested according to EN 13501-1:2018 and achieved a Bfl1-S1.

Footer image

© 2024 WOCA USA, Powered by Shopify


Forgot your password?

Don't have an account yet?
Create account