Maintenance Gel

Maintenance Gel

Product form

SKU: 527802US

  • Revives and renews oil surfaces.
  • Safe for food contact.
  • Makes oil surfaces even more durable.
  • Use as a 2nd coat for a satin sheen.
  • Recommended to maintain UV oil /hardwax oil surfaces.

Revive and protect the beauty of your oiled wood floors with WOCA Maintenance Gel. Designed for furniture, and floors, kitchen work surfaces, it provides a quick-drying, water and dirt-repellent finish that's durable and leaves your wood with a satin sheen. Easily buff out using a polish pad or machine for optimal results, especially on UV-oiled floors. Make your wood shine with WOCA Maintenance Gel.

    Find a Retailer

    Product details

    Specifications

    VOC: 125 g/l, maximum VOC content (A/i (SB)): 500 g/l.

    Density: 0.90-0.95 g/ml.

    Shelf life: 3 years

    Application Temperature: +59-77°F and approx. 50% air humidity.

    Color: Natural

    Cleaning of tools: Use WOCA Solvent or turpentine

    Storage: +50-77°F. Keep out of reach of children. Do not expose to heat (e.g. sunlight). Store frost-free during winter and cool during summer.

    Packaging: 6.763 FL.OZ.

    Dilution: Undiluted

    Odor: Faint

    Solid content: 85-90%

    Mixing ratio: Ready to use. Do not dilute.

    Between coats: 4-6 hours at 68°F

    Light use: 4-6 hours at 68°F

    Recommendation: The oiled surface should not be exposed to water for the first 2-3 days, as this can cause stains and discoloration. Wood humidity must not exceed 18%. High temperature and low air humidity will shorten drying times. Low temperature and high air humidity will extend drying times.

    Fully hard: 3 days at 68°F

    Re-treatment: Repeat the oil treatment when required.

    Instructions
    It is important that both wood and oil are at a temperature of at least 59°F, and ideally about 68°F, and that air humidity is approx. 50 %. Make sure that the room is well-ventilated, for optimal evaporation and drying time. 

    Always remember to test on a less visible spot to check the compatibility of the surface with the product.

     

    Maintenance Gel to re-oil a surface

    1. Thoroughly clean the surface with Intensive Wood Cleaner, mixed 1:20. Then wash with clean water. After cleaning, leave the surface to dry for at least 8-9 hours
    2. Sand the surface with 180 and vacuum clean the surface thoroughly.
    3. Apply an appropriate amount of gel to a Hand Scrubber Flex Kit White and distribute over the surface in a thin, even coat. Continue polishing until the wood seems saturated and the surface has a uniform appearance. It is recommended to work on small areas at a time, as the gel is quick-drying. For larger areas (floors larger than 40 sq.ft./L) it would be advantageous to use a polishing machine.
    4. Remove excess Maintenance Gel with dry, lint-free cotton cloths or pads until the surface no longer appears wet.
    5. If the wood does not seem fully saturated after 4-6 hours, repolish with less gel than the first treatment, but follow the same procedure.
    6. Wait 4-6 hours before using the surface. Avoid getting water or dirt on the wooden surface for the next 3 days .
    Make sure to do a more thorough final polishing to remove all excess gel.
    Maintenance Gel as a 2nd coat to raise oil sheen to satin
    1. Apply a few dime size dabs of Maintenance Gel to a white polishing pad attached to a floor polishing machine. Polish floor well until the wood seems saturated and the surface has a uniform appearance. It is recommended to work on small areas at a time, as the gel is quick-drying. 
    2. Remove excess Maintenance Gel with polishing cloths attached to a clean white pad until the surface no longer appears wet.
    3. Wait 4-6 hours before using the surface. Avoid getting water or dirt on the wooden surface for the next 3 days .
    Make sure to do a more thorough final polishing to remove all excess gel.
    Technical Data Sheet
    Safety Data Sheet
    Certifications

     

    The migration of metals (As, Hg, Se, Cr, Sb, Cd, Pb, Ba) of the sample was tested according EN 71 Part 3 1995. There was no evidence for migration of the named metals above the limit of detection (10-50 ppm). All interior WOCA products are suitable for toys.

    WOCA Maintenance Gel and Worktop oil are tested for specific migration, MOSH/MOAH, NIAS and sensory properties for 2 hours at 104°F under worst-case simulations.

    Related products

    Recommended Products to make your project a success.
    Footer image

    © 2024 WOCA USA, Powered by Shopify

    Login

    Forgot your password?

    Don't have an account yet?
    Create account